Syftet med detta arbete är att simulera ett värmesystem i COMSOL Multiphysics, Pipe flow module, Non-Isothermal Pipe Flow som innehåller ekvationer och randvillkor för att modellera inkompressibel strömning och värmeöverföring i rör.Data om processen och dess komponenter har samlats in från industrin där arbetet är utfört och i vissa fall modifierats för att bättre beskrivas i programmet.Utifrån insamlad data har en modell byggts upp och två simuleringar har gjorts. En stationär för starten av systemet, den har sedan legat till grund för en dynamisk som simulerar förloppet från start till normaldrift.Tiden det tar för det aktuella fallet att nå drifttemperatur är 16 timmar. En felströmning upptäcktes samt att en av pumparna inte kommer att klara en start från 20 °C..

At Forsmarks Kraftgrupp AB (FKA) forces on pipe systems due to transient flow are frequently calculated as a step to verify their structural integrity. In nuclear industries these forces are often calculated with a one dimensional thermal-hydraulic analysis-code called RELAP5. When calculations regarding more complex geometries are needed, the three dimensional code Fluent is often used. This code is highly time consuming and requires large computational power.This projects aim is to compare calculations of pressure, flow and forces carried out by RELAP5 and Fluent for an arbitrary pipe section during transient flow conditions. This has been accomplished by constructing a simple geometry for which a transient flow is simulated in both programs.

In cooperation with the Gislaved company Lerocon AB [1], a separation module wasdesigned as a further supplement to the Module System. The aim of theprojectimplementation was that the separation module could be flexible enough to feed themetal pieces, screws, nuts and other items with large variations of size, appearance andmaterial composition. The module should also be cost effective to manufacture.A separation module is a design which is ment to streamline the work in industries withautomation of the lineoperations. The module feeds the details such as screws, nuts, washersand pieces of metal in a continuous flow in which traps separate the details from each other.Traps may vary depending on the purpose and of the details that are fed. Perhaps it isimportant for the user that the detail-orientation is right after the separation module, whichmeans that all the pieces witch aren´t are fed back in return.For companies and industries in lineoperations that can be made more efficient withautomation, are production flow an important watchword.

The aim is to design a module for living which is flexible in a bigger context, which could condens the city and to answer the questions: How is it possible to make a livingmodule where the compact living theme works in an everyday situation? How is it possible to make one module which is able to function in several different situations? The process in solving problem has been characterized of trial and error: design a module and learn from the mistakes and take the knowledge to the next module. This is the way I have worked until I found a good solution. As a result I can show an efficient module which has several nice values of space and that is flexible and to some part adjust for a disabled person. It can on several ways condens the city.

The dissertation were performed on SP, Technical Institute of Sweden. The dissertation were carried out on the measurement technical department, this dissertation is a part of a bigger project, project ClampCal. One of SP?s returning assignments are flow-measurement. When flow-measurement is performed, the flow has to be stopped so that a meter can be installed in the pipes where measurement is going to take place. At every stop there is time delay in the flow which causes the customers to loose money. This is why SP wanted to find a better solution so that measurement can be done without any stops in the flow. Usage of a so-called Clamp-on meter was considered, but since the measurement uncertainty is too large it takes some investigation on the parts where the largest uncertainties occur and thus find a solution that can diminish the uncertainty as much as possible. The parts that were considered to have an opportunity to reduce measurement uncertainties were the fluid temperature, its characteristics and the pipe geometry and its characteristics. For the fluid temperature a Pt100-sensor with four different radii for various pipes was used.

This master thesis describes the development of an UPS module. UPS is an acronym for Uninterruptable Power Supply. The UPS module has been developed at the company AerotechTelub AB. The UPS module delivers the necessary voltage and current in case of a power interrupt. If a power interrupt occur, the computer system has one to three minutes available to store data and shut down correctly.

At Forsmark nuclear power plant a new course called "education in everyday safety" has been started in an attempt to improve the safety culture. The goal is to spread the of expectations and approach the maintenance management has set, to all employees working at the plants. During the course, theory is mixed with practical tasks to reach a common view how work should be done to achieve safety for the plant and the people that work there.The practical tasks are done inside "maintenance simulators". They are built inside 20 ft containers which contains two dummy pipe systems. On the pipe systems some valves, a flow meter and a pump has been installed.

This report shows methods and workflow when exploring the potential to change Outotecs HCD Silver Electrolysis machine to a module type. It?s done as an attempt to lower the workshop and installation costs and to give customer a more accurate prize directly. To do this a concept was produced which was set to a stress test. Additional objectives were to investigate freight and installation procedures, pneumatic connections and to calculate the difference in cost.Once the concept, a reinforced type of the original frame, was chosen stress tests in computer simulations were made and appropriate alterations were made.

The purpose of this thesis work is to evaluate how the physical behaviour of a pipe bend is affected by the pipe bending procedure. Effects such as initial ovalization, thinning, thickening and plastic hardening from the bending procedure are examined and the mechanical properties of pipe bends containing these effects are investigated.This has been evaluated by creating a detailed Finite Element model of a pipe that is being bent. Then the differences compared to a bent tube in a virgin state, so called Elbow elements and an analytical in-house program have been evaluated. The virgin state refers to a model of a pipe that is bent from the beginning, thus having a homogeneous thickness and not containing any plastic hardening. The Elbow element is a calculationally cheap element, specially developed for accurate calculations of pipe bends in an initially virgin state.The goal with the thesis work is to get a better picture of what happens to a pipe as it is being bent, how this affects the mechanical properties and to evaluate the possibility to develop an easy method for taking these effects into account when using the Elbow element.This report describes the layout of the work and how the detailed FE-model has been constructed.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The purpose of this thesis work is to evaluate how the physical behaviour of a pipe bend is affected by the pipe bending procedure. Effects such as initial ovalization, thinning, thickening and plastic hardening from the bending procedure are examined and the mechanical properties of pipe bends containing these effects are investigated.This has been evaluated by creating a detailed Finite Element model of a pipe that is being bent. Then the differences compared to a bent tube in a virgin state, so called Elbow elements and an analytical in-house program have been evaluated. The virgin state refers to a model of a pipe that is bent from the beginning, thus having a homogeneous thickness and not containing any plastic hardening. The Elbow element is a calculationally cheap element, specially developed for accurate calculations of pipe bends in an initially virgin state.The goal with the thesis work is to get a better picture of what happens to a pipe as it is being bent, how this affects the mechanical properties and to evaluate the possibility to develop an easy method for taking these effects into account when using the Elbow element.This report describes the layout of the work and how the detailed FE-model has been constructed.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.